- Messages
- 904
- Reaction score
- 1,261
- Points
- 93
Westside Conjugate Method Explained for a Powerlifting Training Program and Routine
By Dave Tate
Welcome to what the conjugate method is all about. Conjugate means "to couple". With strength training or powerlifting training you are in the process of trying to combine many methods of training for the development of many different abilities. Not all these methods need the same amount of recovery or change of movement. Using powerlifting as an example you will see what I mean.
Dynamic Work
Because of the SPP of the sport it is best to keep the movements the same. These include the dead lift, bench press and squat. Since the movement stays the same the loading patterns need to change. This is where you see all the different dynamic training cycles. We have two manuals detailing these for the squat, dead lift and bench press. Using many different cycles is very important for constant progress.
Because of the increased intensity (the load) needed to use this method for powerlifting training the cycles are more limited. The GPP and experience of the lifter also limits the number of weeks one can use the same movement. The point is this movement may need to change every one to three weeks. There are several articles addressing the max effort work available at EFS.
These are the main movements you use to drive your lifts. These are different for everyone but could include 4 board presses, GHR, Shoulder Presses and so on. These will be the movement that you feel and know have a direct relationship with your three main lifts. It is very important to train the hell out of these movements so longer cycles can and should be used with higher rep ranges. These movements might cycle for 8-12 weeks. Remember that these are movements that you know can directly influence your main lifts. Choose these wisely!
Most lifters will keep these main movements in during the entire meet training phase. The key is to change the load, sets and reps in a direct attempt to make these lifts as strong as you can.
These are the movements and methods that are used to build mass (if needed). These can change every session and to tear the body down as much as you can. This work should not be part of a pre contest phase. Recovery is more important than mass at this time.
This is the crap you have to do to keep from getting beat up. This could be external rotator work, lower back work and so on. Usually higher reps are used with lower intensities so movement change does not have to happen that often. These should not be too taxing. Remember that these movements are for pre-hab and are not supplemental work. So you don?t have to have the same kind of RPE for these movements as you would for your max effort, dynamic or supplemental work.
If needed, these movements will not change. But always be learning new ones if need be.
Some abilities may be de-loaded while others are being pounded. This should be the way most of the year goes. Before a meet or when worn down a full blown de-load should take place. A full blown de-load will involve de-loading all abilities.
This process will change based upon what sport you are involved in because of different types of skill based training.
By Dave Tate
Welcome to what the conjugate method is all about. Conjugate means "to couple". With strength training or powerlifting training you are in the process of trying to combine many methods of training for the development of many different abilities. Not all these methods need the same amount of recovery or change of movement. Using powerlifting as an example you will see what I mean.
Dynamic Work
Because of the SPP of the sport it is best to keep the movements the same. These include the dead lift, bench press and squat. Since the movement stays the same the loading patterns need to change. This is where you see all the different dynamic training cycles. We have two manuals detailing these for the squat, dead lift and bench press. Using many different cycles is very important for constant progress.
- Average Cycle Length - 3-4 weeks
- De-load - after one or two cycles
Because of the increased intensity (the load) needed to use this method for powerlifting training the cycles are more limited. The GPP and experience of the lifter also limits the number of weeks one can use the same movement. The point is this movement may need to change every one to three weeks. There are several articles addressing the max effort work available at EFS.
- Average Cycle Length - 1-3 weeks
- De-load - every 3 to 6 weeks
These are the main movements you use to drive your lifts. These are different for everyone but could include 4 board presses, GHR, Shoulder Presses and so on. These will be the movement that you feel and know have a direct relationship with your three main lifts. It is very important to train the hell out of these movements so longer cycles can and should be used with higher rep ranges. These movements might cycle for 8-12 weeks. Remember that these are movements that you know can directly influence your main lifts. Choose these wisely!
Most lifters will keep these main movements in during the entire meet training phase. The key is to change the load, sets and reps in a direct attempt to make these lifts as strong as you can.
- Average Cycle Length - 5-8 weeks
- De-load - every 8 to 10 weeks
These are the movements and methods that are used to build mass (if needed). These can change every session and to tear the body down as much as you can. This work should not be part of a pre contest phase. Recovery is more important than mass at this time.
- Average Cycle Length ? N/A
- De-load - every 6-8 weeks
This is the crap you have to do to keep from getting beat up. This could be external rotator work, lower back work and so on. Usually higher reps are used with lower intensities so movement change does not have to happen that often. These should not be too taxing. Remember that these movements are for pre-hab and are not supplemental work. So you don?t have to have the same kind of RPE for these movements as you would for your max effort, dynamic or supplemental work.
- Average Cycle Length - 8-12 weeks
- De-load - every 8-12 weeks
If needed, these movements will not change. But always be learning new ones if need be.
- Average Cycle Length ? N/A
- De-load ? N/A
Some abilities may be de-loaded while others are being pounded. This should be the way most of the year goes. Before a meet or when worn down a full blown de-load should take place. A full blown de-load will involve de-loading all abilities.
This process will change based upon what sport you are involved in because of different types of skill based training.